EV CPS2.9 PDF
Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS
|Published (Last):||14 June 2004|
|PDF File Size:||2.62 Mb|
|ePub File Size:||16.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
Also See for CPS2. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
This mode of operation is being used for all 2-channel applications, like stereo operation. Enter text from picture: Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Electrovoice contractor precision cps2t: Controls, Indicators and Connections Front View 1. Turning the control to the right increases and turning it to the left decreases the volume.
For fixed amplifier installations in a device control room that cps2. a central air-cooling system or air conditioners, calculating the maximum heat emission may be necessary.
Please take time to consult this manual so that you can understand cpps2.9 the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities. Page of 24 Go. Electrovoice compact precision cps: Following table shows possible switch settings and corresponding delay times. Show all Contractor precision cps2.
A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier. Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported.
Failure to do so may result in damage to the power amplifier as well as to the rack case. PARALLEL operation is the mode of choice, whenever the same input signal drives multiple power amp channels of a large system installation. Brackets for securing the power amplifier are available as accessories. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation.
Electro-voice CPS Manuals
Connect the power amplifier only to a mains network, which corresponds to the requirements indicated on the type plate. The connected speaker systems must be able to handle such voltages.
Mounting CPS amplifiers have been designed for installation in a conventional inch rack case. By pressing ‘print’ button you will print only current page. The audio signal has to be applied to the input connectors of channel 1.
This mode of operation is being used for all 2-channel applications, like stereo operation. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
CPS amplifiers have been designed for installation in a conventional inch rack case.
Don’t show me this message again. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the For pricing options and packages, contact us at The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier.
The audio signal has cpa2.9 be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration.
Mains Switch The Mains Switch on the front panel separates the power amp from the mains. F reserved Table 4. Keep ventilation louvers free from dust to ensure xps2.9 airflow. Set the switch to the 50 Hz position for activating the High Pass Filter. Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred.
Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Set the switch to the OFF position if no attenuation of low frequency audio signals is required. The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat.
The Mains Switch on the front panel separates the power amp from the mains. Please read and follow the instructions provided in the documentation that you have received together with each extension module. This manual also for: Do not modify this unit!
Attach the power cpd2.9 as shown in the illustration using 4 case nuts and screws.