ULC is pleased to announce the publication of the Fifth Edition of CAN/ULC- S, Standard for. Inspection and Testing of Fire Alarm Systems. This National. Fire Alarm Inspection, Maintenance, and Service by Anubis Systems Technologies. SCOPE. This Standard provides requirements for the inspection and testing of fire alarm systems and specifies the devices and functions to be inspected.

Author: Tojat Ferr
Country: Monaco
Language: English (Spanish)
Genre: Business
Published (Last): 26 March 2018
Pages: 348
PDF File Size: 17.3 Mb
ePub File Size: 12.66 Mb
ISBN: 737-2-78519-417-6
Downloads: 94399
Price: Free* [*Free Regsitration Required]
Uploader: Fern

The tests reported on this form do not include the actual operational test of ancillary devices except where noted. A B C Confirm that a trouble signal is received at the control unit or transponder under an open loop fault. Main Power supply failure trouble signal operates. Building diagrams are on site that clearly indicate the type and location of all smoke control equipment fans, dampers, etc.

Yes Last Service Date: Oil level in normal range on air compressor? The common control employs several features to enable the occupants to identify any specific problems within the system. Use only alkaline or lithium type batteries and make sure you double check the expiry date on the battery and test it before you place it in the unit. Intelligibility clarity of voice messages confirmed.

Zones or module numbers if the system being tested is addressable must be recorded for each field device on the Individual Device Test Record ; End-of-Line devices resistors – these have to be listed along with their locations on the Individual Device Test Record cab specific testing must be conducted that requires their physical dismounting and re-installation; Isolators data buss, power buss, and in-suite signal isolators – these have to be listed on the Individual Device Test Record including a reference to their actual location and some may require physical dismounting in order to affect a proper test; Smoke detector sensitivity readings – results must be recorded on the Individual Device Test Record.

Related Posts  FD M760 PDF

Cabinets have no corroded or damaged parts?

Standards Council of Canada

Never paint the sensor! Sprinkler System Testing Continued: Restricting orifice in place? Ionization type smoke detectors utilize a small source of radioactive material usually Americium that in fact ionizes airborne particulates and attracts them to to one side or the other of a polarized grid. Trouble signal on the voice communication ulcc results in common trouble signal on the fire alarm system.

Tested for Operation results are recorded in the Device Test Record. Audibility of d536 sounder checked? Most fire alarm systems employ zoned annunciators so that fire fighting personnel can be dispatched to the proper area of the building.

Fire Alarm System Periodic Inspection (CAN/ULC-S)

Hydraulic name plate is properly affixed to the sprinkler riser? Hose Connection Pressure Reducing Valves: Jockey pump operational and uld good condition? Main Drain test shall be conducted on each system riser. Standard sprinklers less than 50 yrs old. Individual alarm and supervisory zone indication operates.

Powered independently of the fire alarm control, these devices are normally not connected to it. Check the date stamp located on the back of the detector and ensure you follow the care and maintenance instructions that came with it to make sure to keep it operating at peak efficiency. Proper light function – power loss? Fuel acn and a low fuel trouble indication the low fuel alarm set point should be checked to ensure s5366 unit is able to deliver emergency power for the duration required by the Building Code for the type of occupancy; In-suite signals if equipped with a silence feature must be checked for proper operation of the silence function including resounding if d536 are silenced and a second alarm zone is activated ; Duct mounted smoke detectors must be individually tested and some rather detailed results recorded namely the differential pressure and the sensitivity reading on the Individual Device Test Record ; Stand-alone s56 of networked systems must be tested and properly documented; Sprinkler system interconnection isolation valve supervisory signals, flow switch alarm, tamper, low temperature, heat trace controller trouble and supervisory, low air, etc.


L Inspected for electrolyte leakage.

Photoelectric type 5s36 detectors ulv an infrared light source called the emitter and a receiver, both of which are located inside the sensing chamber. Individual alarm and supervisory input zone designation labels are properly identified. Annual Testing – The Annual Ccan of the fire alarm system is performed by qualified technical personnel to a specific National Standard. Abnormally frequent false tripping of dry-pipe valves?

While in standby mode, voice communication busses used for paging, alert signal, alarm signal, and emergency telephone communication circuits, an Q open circuit fault, or short circuit fault, or operation of an overcurrent protective device provided for the purpose, shall result in a specific trouble indication specific to the faulty buss. Audible trouble signal operates.

Cooling water level is normal Inspect exhaust hangers and supports? You can download a convenient monthly test record in PDF format.

CAN/ULC-S536-04 Fire Alarm Annual Inspection Test Form

Refer to Appendix F1 ; P iii Silent accelerated s36. Flow Test – by flowing the required volume of water at design pressure to the hydraulically most remote hose connection? Yes No Oil Pressure: Identify zone, circuit number, or address. It’s also prone to false alarms when installed close to bathrooms or kitchens with older style dishwashers.

G Test to ensure lights function for a duration equal to design criteria? Are above results comparable to previous tests?