ASTM A682 PDF

0 Comments

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Kakazahn Vusar
Country: Cape Verde
Language: English (Spanish)
Genre: Education
Published (Last): 25 December 2014
Pages: 66
PDF File Size: 17.87 Mb
ePub File Size: 4.48 Mb
ISBN: 696-2-43092-164-6
Downloads: 73724
Price: Free* [*Free Regsitration Required]
Uploader: Kazigul

Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi? NOTE 2—Camber tolerances as shown in the table are for any 8 ft.

Normal coiling or piling does not provide a 3 Where an ellipsis. Over 12 Through 11? However, under SI the preferred term in mass. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. A superscript epsilon e indicates an editorial change since the last revision or reapproval. However, under SI the preferred term in mass. Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document.

ASTM A, AM_百度文库

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard has been approved for use by agencies of the Department of Defense.

NOTE 3—When the camber tolerances shown in Table 8 w682 not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened. Current edition approved March 10, This is produced when the edge condition is not a critical requirement for the? Conformance to SI tolerances is mandatory when the “M” specification is used.

Limits on such elements are by agreement between purchaser and supplier. Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size.

Related Posts  KAFKA ODRADEK PDF

Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production. Dimensions, Mass, and Permissible Variations 9.

The material must be adequately protected and correctly identi? NOTE 2—The industry de?

ASTM A Steel, Strip, High Carbon, Cold Rolled, General Requirements

Over 12 Width Tolerance, Plus and Minus, in. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address zstm at phonefaxor service astm.

C When edge, width and thickness are not de? In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing.

ASTM A682 Grade 1074

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Originally published as A — The elements comprising the desired chemical composition are speci? However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values.

The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. A portion of the coil may be discarded prior to cutting the samples for retest. The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci?

Thickness Tolerances Plus or Minus, in. Within the text, the SI units are shown in brackets. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. If any of the retests fail to comply with the requirements, the coil shall be rejected. B The sum of copper, nickel, chromium, and molybdenum shall not exceed 0.

Related Posts  CHUKOVSKAYA SOFIA PETROVNA PDF

Combining values from the two systems will result in nonconformance with the specification. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis. When agreed by purchaser and supplier, other silicon ranges are permissible.

When required, minimum coil weights are subject to negotiation. Two additional samples are secured from each end of the coil from which the original sample was taken. Strip is classified as product that is 0. However, the document shall clearly identify the organization submitting the document. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Within the text, the SI units are shown in brackets. When the amount of vanadium, columbium, or titanium is less than 0.

When one or more of these elements is speci? Strip tolerance products may be available in widths wider than ? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Referenced Documents purchase separately The documents listed below are referenced a862 the subject standard but are not provided 6a82 part of the standard. Conformance to SI tolerances is mandatory when the “M” specification is used. For strip length under 8 ft.