ENCODER HT12E PDF

0 Comments

The HT12E is a 2^12 encoder in 18 pin DIP package. This is CMOS LSI for remote control system applications. It is capable of encoding information which. Make a RF Transmitter and Receiver With HT12E & HT12D: Would you like to With the help of our friends HT12E (ENCODER) and HT12D (DECODER) and a. Dec 8, HT12E is an encoder integrated circuit of 2 12 series of encoders. They are paired with 2 12 series of decoders for use in remote control system.

Author: Grogar Kaktilar
Country: Algeria
Language: English (Spanish)
Genre: Software
Published (Last): 28 October 2014
Pages: 127
PDF File Size: 14.40 Mb
ePub File Size: 1.76 Mb
ISBN: 947-9-95259-403-6
Downloads: 76696
Price: Free* [*Free Regsitration Required]
Uploader: Arashilmaran

However if you need to have more address combinations then you might want to look for other encoder-decoder pair available in the market. Supply voltage; 5V 2. Choosing Battery for Robots.

Skip to main content. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the enncoder A0 to A7.

Submitted by admin on 30 October Feel free to comment and post your queries regarding this post we are happy to assist you. Notify ht2e all new follow-up comments Notify of new replies to all my comments. The encoder IC will be in standby mode if the TE pin is disabled and thus the status of ht12f pin was necessary for encoding process.

Related Posts  EPIA EN12000 PDF

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

If you need more address I suggest you to look for any other encoders and decoders jt12e more address combinations. Connected to the Ground of circuit. No mechanical switching involved.

Dear Frank Donald, Thank you for the reply and clarification. Regarding the addressing you can use a simple switch to feed your desired address.

These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

Arduino ht1e2 GPS receiver. Calculating addresses, we are limited to 56 addresses per pair. Posted by Palakkumar Patel at This high-density System-in-Package SiP integrates controller, power switches, and support components.

Related Posts  75175 DATASHEET PDF

HT12E Encoder IC buy online in India – Robomart

These 12 bits are divided into 8 address bits and 4 data bits. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. HT12E starts working with a low signal on the TE pin.

Quote and Order boards in minutes on: There are address combinations which I feel will do a encodef job in securing the communication and keep away interference.

HT12E Encoder IC

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. Interface GPS with Arduino.

Can range from 2. The IC is has a wide range of operating voltage from 2. Encoddr if i want to transmit data in 5th encoder, in which pin of encoder sholud i provide data to encoder??? If you want security you can connect any of the 8 pins to 5V to make it high. Encooder can also be connected to switches to manually send and receive data. They are paired with 2 12 series of decoders for use in remote control system applications.

The above diagram shows the practical set up of the HT12E encoder IC for better understanding on the working.